Configuring WireGuard in LibreELEC (v9.2.1 and newer)

LibreELEC can be configured as a WireGuard VPN client allowing you to accessing media in a remote location or tunnel traffic to avoid local inspection of network activity. This guide assumes configuration of a single WireGuard tunnel that is persistent, i.e. activated on device boot so that Kodi network traffic is routed through the WireGuard VPN tunnel.

WireGuard tunnels are managed by a ConnMan VPN plugin (connman-vpn.service) that acts as a companion to the main network connection manager daemon (connman.service). The VPN plugin watches /storage/.config/wireguard/*.config and will attempt to define ConnMan services from auto-discovered configuration files. Once a valid ConnMan WireGuard .config has been imported it can be connected; either manually using connmanctl from the SSH console or scripted from a systemd service that runs on boot. Connections can also be controlled manually from the network 'Connections' tab in the LibreELEC settings add-on which connects and disconnects WireGuard (ConnMan) services via d-bus.

Note: ConnMan uses its own configuration file format (shown below). You cannot import/use the WireGuard configuration files exported from most WireGuard server tools and third-party VPN services - the format is different. The files will contain everything you need, but you must transpose the information into the ConnMan format:

Type = WireGuard
Name = WireGuard (Home)
Host =
Domain = my.home.vpn
WireGuard.Address =
WireGuard.ListenPort = 51820
WireGuard.PrivateKey = qKIj010hDdWSjQQyVCnEgthLXusBgm3I6HWrJUaJymc=
WireGuard.PublicKey = zzqUfWGIil6QxrAGz77HE5BGUEdD2PgHYnCg3CDKagE=
WireGuard.PresharedKey = DfEYeVs04HS9XhKGM4/ZXHG3Qc4MFK2AJd8XouYDbRQ=
WireGuard.DNS =,
WireGuard.AllowedIPs =
WireGuard.EndpointPort = 51820
WireGuard.PersistentKeepalive = 25


Name = AnythingYouLike
Host = IP of the WireGuard server
Domain =
WireGuard.Address = The internal IP of the client node, usually a /24 address
WireGuard.ListenPort = The client listen port (optional)
WireGuard.PrivateKey = The client private key
WireGuard.PublicKey = The server public key
WireGuard.PresharedKey = The server pre-shared key (optional)
WireGuard.DNS = Nameserver to be used with the connection (optional)
WireGuard.AllowedIPs = Subnets accessed via the tunnel, means “route all traffic”
WireGuard.EndpointPort = The server ListenPort
WireGuard.PersistentKeepalive = Periodic keepalive in seconds (optional)

Domain is a quirk of how ConnMan internally names and stores services, and it must exist. It is simply a text field, not a qualified domain, so “MyVPN” and “alice.loves.bob” and “” are all valid Domain entries.

Creating WireGuard Keys

If you need to create some, run “wg-keygen” from the SSH console and /storage/.cache/wireguard will contain new publickey, priatekey, and preshared files with keys inside. Most users will not need to generate WireGuard keys as they will be in the configuration file provided by a VPN service provider.

Testing Connections

Once you have saved a configuration file, check it is valid:

RPi4:~ # connmanctl services
* R home              vpn_185_210_30_121_my_home_vpn
*AO Wired                ethernet_dca622135939_cable

In the above example “vpn_185_210_30_121_my_home_vpn” was created (vpn_Host_Domain) as the ConnMan service name. Test the service will connect using:

RPi4:~ # connmanctl connect vpn_185_210_30_121_my_home_vpn

ConnMan will create a new network interface, so “ifconfig” will show wg0 (sometimes wg1, wg2), e.g.

RPi4:~ # ifconfig
eth0      Link encap:Ethernet  HWaddr DC:A6:32:13:26:3b  
          inet addr:  Bcast:  Mask:
          RX packets:3136938 errors:0 dropped:40816 overruns:0 frame:0
          TX packets:242506 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:1000 
          RX bytes:310409413 (296.0 MiB)  TX bytes:22433323 (21.3 MiB)

lo        Link encap:Local Loopback  
          inet addr:  Mask:
          inet6 addr: ::1/128 Scope:Host
          UP LOOPBACK RUNNING  MTU:65536  Metric:1
          RX packets:6109 errors:0 dropped:0 overruns:0 frame:0
          TX packets:6109 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:1000 
          RX bytes:415013 (405.2 KiB)  TX bytes:415013 (405.2 KiB)

wg0       Link encap:UNSPEC  HWaddr 00-00-00-00-00-00-00-00-00-00-00-00-00-00-00-00  
          inet addr:  P-t-P:  Mask:
          UP POINTOPOINT RUNNING NOARP  MTU:1420  Metric:1
          RX packets:13744 errors:0 dropped:0 overruns:0 frame:0
          TX packets:11080 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:1000 
          RX bytes:13775220 (13.1 MiB)  TX bytes:1232552 (1.1 MiB)

You should be able to “ping” the remote (server) side of the WireGuard VPN tunnel. In our example this is

RPi4:~ # ping
PING ( 56 data bytes
64 bytes from seq=0 ttl=64 time=147.936 ms
64 bytes from seq=1 ttl=64 time=147.955 ms

The routing table will show normal traffic routed to the wg0 interface:

RPi4:~ # route
Kernel IP routing table
Destination     Gateway         Genmask         Flags Metric Ref    Use Iface
default         *              U     0      0        0 wg0         *      UH    0      0        0 wg0         *      UH    0      0        0 wg0        *        U     0      0        0 wg0    *        U     0      0        0 eth0    *      UH    0      0        0 eth0 UGH   0      0        0 eth0

To disconnect the ConnMan service:

RPi4:~ # connmanctl disconnect vpn_185_210_30_121_my_home_vpn

Check “ifconfig” again and the WireGuard interface will be gone.

Configuring Systemd

To start the connection automatically on boot we need to create a systemd wireguard.service file. This tells ConnMan which service to start and the sequence/dependencies (when to start it). The sample wireguard.service file looks like:

Description=WireGuard VPN Service connman-vpn.service connman-vpn.service

ExecStart=/usr/bin/connmanctl connect vpn_service_name_goes_here
ExecStop=/usr/bin/connmanctl disconnect vpn_service_name_goes_here


Copy the sample wireguard.service file to /storage/.config/system.d/wireguard.service:

cp /storage/.config/system.d/wireguard.service.sample /storage/.config/system.d/wireguard.service

Replace vpn_service_name_goes_here with your service name, e.g. vpn_185_210_30_121_my_home_vpn using nano. Use “ctrl+o” to save changes and “ctrl+x” to exit nano:

nano /storage/.config/system.d/wireguard.service

Now we can enable and start the service:

RPi4:~ # systemctl enable /storage/.config/system.d/wireguard.service
Created symlink /storage/.config/system.d/ → /storage/.config/system.d/wireguard.service.
RPi4:~ # systemctl start wireguard.service

Congrats! .. all is done. Check the WireGuard tunnel is active using “ifconfig” and “ping” and if all is good, reboot to test the WireGuard tunnel comes up automatically on boot.


Big thanks to ConnMan maintainer Daniel Wagner from the Open Source group at Intel who has worked with Team LibreELEC staff to implement WireGuard support in ConnMan (he wrote the code, we tested it). Thanks wagi!